Vista Ademco -10SE Instrukcja Naprawy Pobierz pdf (Strona 87)

DIALER

PROGRAMMING

(~)

*34

*35

*36

*37

*36

ALARM BELL TIMEOUT

—

This field determineswhether the external sounder will shut off after

time allotted,or continueuntil manually turned off. Enter as follows

O= No timeout 1 = 4 rnin (default); 2 = 8 ti, 3 = 12 min.

Alarm bell timeout must be set for a

minimum of 4 min (“1=)

for UL installations.

ZONE TYPE

01 ENTRY DELAY Partition1 ❑ Partition2 ❑

Systemwill wait the time allottedbeforesounding alarm upon

entering. May be selectedindividually for eachPartition.

o= Oseconds 2 =30 seconds 4 =60 seconds

1 =20 seconds 3 =45 seconds 5 =90 seconds

Default is 2 (30 seconds).Entry delay must be set for a maximum

of 20 seconds in UL installations.

Zone~ 02 Entry Delay= ZoneType 01 Entry Delay+ 30 seconds.

(EXIT delays= Zonetype 01 En@ delay plus 40 seconds).

AUDIBLE EXIT WARNING

Partition1

❑

Psrtition2 ❑

If enabled,this field provides exit warning sound when armed AWAY

it canbe selectedfor either or both Partitions.

Warning sound consistsof slowcontinuous beepsuntil last 5 seconds,

when it changes to fast beeps. The warning sound will end at the

termination of Exit time.

O= no; 1 = yes.Default is 1.

CONFIRMATION OF ARMING DING Part%1

❑ %rt?n2 ❑

Enter 1 (in either or both Partitions) to enable l/2 second external

alarm sounding“ding” when closingreport goesin, or at the end of exit

delay.Odisablesthe “iii@’ (default).

POWER UP IN PREVIOUS STATE

•1

Enter 1 for Yes (default) if, upon power-up, you want the system to

assumethe systemstatusprior to power down. Enter O if you want the

systemto alwayspowerup in a disarmed state.

When the systempowersup armed, an alarm will occur1 minute after

arming if a zoneis faulted. Must be *1” for UL installations.

Note that if the previous state was armed AWAY or STAY, the system

will not respondto sensorchangesfor 1 minute, which allowstime for

sensorssuchasPIRs to stabilize.

Enter up- to- the

number of digits

shown. Do not fill

unused spaces.

Enter O-9,

# + 11 for ‘*’

# + 12 for%’

# + 13 for a pause

(2.5 sees)

PABX ACCESS CODE (See Box at Left)

Ill

Enter up to 4 digits if PABX is needed to accessan outside line. If

fewer than 4 digits are needed to be entered, exit by pressing * and

next field number (e.g.,41). To clearenlries horn field, press ZO*.

PRIMARY PHONE No. (See Box at Left)

1111111111!

Enter up to 12 digits. If fewer than 12 digits entered, exit by pressing

*ad na field n~ber (e.g.,42).

TO clear entries from field, press

%1*.

Note: Back-up reporting (8 calls are made to the secondary phone

number if no kiss-off is received after 8 attempts to the primary

number) is automaticonly if there is a second- phone number (field

*42).

SECONDARY PHONE No. (See Box at Left)

11111111111

Enter up to 12 digits. If fewer than 12 digits entered,exit by pressing

* and next field number (e.g., 43). To clear entries from field, press

*42*. SeeNote above,also.

47-

1 2 ... 82 83 84 85 86 87 88 89 90 91 92 ... 119 120

Komentarze do niniejszej Instrukcji

Brak uwag

Vista Ademco -10SE Instrukcja Naprawy Strona 87

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Vista Ademco -10SE