Vista Ademco -10SE Instrukcja Naprawy Pobierz pdf (Strona 103)

Trouble Conditions

(See Troubleshooting Guide also)

General

Infomnation

,~~t, ~

“Batter#’ Dieplaye

Telephone tie Failnre

Power Faihwa

other Displaye

(Fixed Word displays are

in parentheses)

The word “CHECK” on the Keypads display, accompanied by a rapid

“beeping” at the Keypad, indicates that there is a trouble condition in the

system. The audible warning sound can be silencedby pressing any key.

Instruct users to call fm serviceimmediately upon seeingany of the following

messages.

● A display of “CHECK’ and one or more zone numbers indicatesthat

a problem existswith the displayedzone(s)and requires attention.

Note: The controlwill sense a high resistancein the loops on hard-wired

zones 2-8 and display “CHECK” and the afYectedzone number when the

system is in the disamnedmode.It will not be possibleto arm the system

as long as this condition exists (unless this zone is bypassed). If the

system is in the armed mode when the high resistancecondition occurs,

this display will not appear, but will do so as soon as the system is

disarmed. Checkthe sensoror the loopwiring for the displayed zone.

When the problem has been corrected, the display can be cleared by

entering the OFF sequence(codeplus OFF key) twice.

● A display of “CHEC~ and 09 indicates that communication between

control and a zone expanderor wirelessreceiveris interrupted. Checkthe

wiring and DIP switchsettingson the units.

“ If there are wireless sensors in the systenL the CHECK conditionmay

also be caused by some change in the environment that prevents the

receiverfrom receivingsignalshorn a particular sensor.

“ A display of ‘RAT’ (Fixed-wordkeypads)or KSYSTEM LO BAT (Alpha

keypads) with no zone number indicatesthat the system’smain standby

battery is weak.

● A display of “BAT’ (Fixed-word keypads) or LO BAT (Alpha keypads)

with a zone number and a once per minute “beeping at tie keypad

indicates that a low battery condition exists in the wireless sensor

displayed (zone “00” indicates a wireless keypad). If the battery is not

replacedwitbin 30 days, a CHECK display may occur.

Note: Some wireless sensorscontain a non-replaceable long-life battery

which requires replacement of the entire unit at the end of battery life

(e.g.,Nos. 5802, 5802CP, 5803).

A display of %4” (Fixed-word keypads), or “Telco Fault” (Alpha keypads),

indicates that a monitored telephoneline (if programmed in field *2) has

been cut (or disconnected). Depending on how the systemwas programm~

the keypad may alsoproducea trouble sound, and the external sounder may

be activated(silenceby enteringinstaller codeplus OFF).

●

If there is no keypad display at all, and the POWER indicator (if

present) is not lit,

operating power for the systemhas stopped and the

systemis inoperative.

If the message “AC LOSS” (Alpha keypads) or ‘NO AC” (Fixed-word

keypads) is displayed, and the POWER indicator (if Present) is off,

the keypad is operating on battery power only.

M the battery standby capacity is

used UP during a prolonged AC

power out&~, the coritrol’~a~ary Power-ti shu; dofi to ~e

deepdischsrgeof the battery.

Busy-Standby (dI). If this remains displayed for more than 1 minute, the

systemis disabled.

Modem Comrn (CC) The system is in communication with the central

station for changeof fimction or statusverification.

Conum Failure (FC) A communicationfailure has occurred.

Open Circuit (OC) The keypadis not receivingsignalsflom the controland

seesan open circuit.

Long Rng l?rbl (bF) Back-up LRR communicationfailure.

-103-

1 2 ... 98 99 100 101 102 103 104 105 106 107 108 ... 119 120

Komentarze do niniejszej Instrukcji

Brak uwag

Vista Ademco -10SE Instrukcja Naprawy Strona 103

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Vista Ademco -10SE