Vista Ademco -10SE Instrukcja Naprawy Pobierz pdf (Strona 34)

Instal/jointfilesconvert/304319/bg the 5SOOTM Module

Installation of this module is necessaryonly if you are using one or more

5827BD Wireless Bi-directionalkeypads.

Note: The 5827BD wiIl only receivesignalsfor”partition1.

Motmting the 5SOOTM Module

The 5800TM must be locatednext to the RF receiver (between one and two

feet born the receiver’santennas).The 5800’I!Mmust not be installed within

the control cabinet. Mount the unit using its accompanying mounting

bracket.

5SO07M W*S

COfmedions

Connect

the 5800TM to the control panel’s keypad connection terminals,

using the suppliedconnectorwith flying leads,as follows:

WIRE TERMINAL ON CONTROL

BLACK (Ground):

Terminal4

RED (+12VDC)

Terminal5

GREEN (DatatoControl)

Terminsl6

YELLOW (DatafimmControl)

Terminal7

BLUE: NotUsed

Do not cut any of the jumpers on the 5800TM when using it with the

Vista-20.

For additional information,refer to the 5800TMs inshmtions.

5800 Series Transmitters

5800 series transmitters have built-in serial numbers that must be “learned

by the systemusing the *56 or *83 interactive mode, or input to the control

via the downloader. 5800 series transmitters (except 5827 described

separately)do not have DIP switches.

Each transmitter’s zonenumber is programmed into the systemin *56 mode.

Some transmitters, such as the 5816 and 5817, can support more than one

“zone”(referredto asloopsor inputs). On the 5816 for example,the wire con-

nection terminal blockis loop 1, the reed contactis loop 2. Each loop must be

assigneda difFerentzonenumber.

For button transmitters (RF “keys”), such as the 5803 ~d 5801, YOUmust

assign a unique zone number to each individual button used on the

transmitter. Each button on the transmitter also has a pre-designated loop

or input number, whichis automaticallydisplayed.

Programming

an RF House ID (01-31) in field *24 is necessary only if

using 5827 or 5827BD wireless keypads. An RF House ID is not

necessaryfor other 5800 series transmitters and the entry should be left at

’00” (default) in thosecases.

The 5827 reportslow battery statusas zone “00.”

Transmitter Sal

m==-

Except for some transmitters that may be carried off-premises (5802,

5802CP, 5803, and 5827, and 5827BD), each transmitter is supervised by a

check-in signal that is sent to the receiver at 70-90 minute intervals. If at

least one check-inis not receivedfrom each

supervised transmitter within a

12-hour period, the “’missing”transmitter number(s) and “CHECK” will be

displayed.

The supervision for a particular transmitter in the systemthat may also be

carried off the premises(5801, 5802MN) maybe med off by leg it as a

“UIt” (unsupervisedRF) type, as describedlater,

5800 seriestransmittershave built-in tarnper protectionand will annunciate

as a “CHECK!’ conditionif coversare removed.

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 119 120

Komentarze do niniejszej Instrukcji

Brak uwag

Vista Ademco -10SE Instrukcja Naprawy Strona 34

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Vista Ademco -10SE