Vista Ademco -10SE Instrukcja Naprawy Pobierz pdf (Strona 28)

100

–28–

Installing 5800 Series Transmitters

To be sure reception of the transmitter's signal at the proposed mounting location

is adequate, perform a Go/No Go test.

Go/No Go Test Mode

The Go/No Go tests will verify adequate RF signal strength from the proposed

transmitter location, and allow you to reorient or relocate transmitters if

necessary, before mounting the transmitters permanently.

This mode is similar to the transmitter test mode , except that the wireless

receiver gain is reduced. This will enable you to make sure that the RF signal

from each transmitter is received with sufficient signal amplitude when the

system is in the normal operating mode.

1. With at least one 2-line Alpha keypad (5137AD or 6139) connected to the

system, power up the system temporarily. If you had previously connected

the AC transformer to the control panel, you need only plug in the

transformer (to 120VAC outlet) to power up the system.

2. Enter installer code (4112) + [#] + 4 from partition 1's keypad. For multi-

partition systems, make sure all partitions are disarmed before entering this

mode.

3. Once you have placed transmitters in their desired locations and the

approximate length of wire to be run to sensors is connected to the

transmitter's screw terminals (if used), fault each transmitter. Do not conduct

this test with your hand wrapped around the transmitter as this will cause

inaccurate results.

Note: On button type transmitters whose buttons have been set to Arm

Away, Arm Stay, or Disarm, pressing a button will take the system out of the

Go/No Go Test mode and cause that action.

a. The keypad will beep three times to indicate signal reception and display

the appropriate zone number.

b. If the keypad does not beep, reorient or move the transmitter to another

location. Usually a few inches in either direction is all that is required.

4. If each transmitter produces the proper keypad response when it is faulted,

you can then permanently mount each of the transmitters according to the

instructions provided with them.

5. Exit the Go/No Go test mode by entering: Installer code (4112) + OFF.

6 Unplug the AC transformer.

Setting DIP switches on the 5827 Transmitter(s)

A 5827 transmitter must be set to the programmed House ID, using its DIP

switches.

5827 Wireless Keypad DIP Switch Table

1 2 3 4 5

SWITCH UP FOR “ON”

SWITCH DOWN FOR “OFF”

HOUSE ID

SHOWN SET FOR HOUSE ID# 30

HOUSE

DIP SWITCH POSITION

12345

1 ––––UP

2 – – – UP –

3 – – – UP UP

4––UP––

5––UP–UP

6––UPUP–

7––UPUPUP

8 –UP–––

9 – UP – – UP

10 – UP – UP –

11 – UP – UP UP

12 – UP UP – –

13 – UP UP – UP

14 – UP UP UP –

15 – UP UP UP UP

16 UP – – – –

HOUSE

DIP SWITCH POSITION

1 2345

17 UP – – – UP

18 UP – – UP –

19 UP – – UP UP

20 UP – UP – –

21 UP – UP – UP

22 UP – UP UP –

23 UP – UP UP UP

24 UP UP – – –

25 UP UP – – UP

26 UP UP – UP –

27 UP UP – UP UP

28 UP UP UP – –

29 UP UP UP – UP

30 UP UP UP UP –

31 UP UP UP UP UP

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 99 100

Komentarze do niniejszej Instrukcji

Brak uwag

Vista Ademco -10SE Instrukcja Naprawy Strona 28

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Vista Ademco -10SE